Install A Roll-Up Doo, It can be hard and time-consuming to find and install the right roll-up garage door for your home or business. This article will help you get organized and learn how to install a sectional roll-up garage door. Putting in a rollup garage door is different from putting in other types of garage doors. This article can help you through the process.
A Brief Look at Installing a Roll-Up Garage Door
Roll-up garage doors are different from traditional garage doors because they don’t lay flat on the ceiling of your garage. Instead, they coil in on themselves. In order to coil, this method needs special panels, mechanics, and installation. Install A Roll Up Doo, Garage doors that roll up are made of smaller slatted panels that are about 3 inches tall.
One benefit of rollup garage doors is that they are usually made of thicker and more secure materials than other types of garage doors. For example, rollup garage doors are made of metal that is 18 gauge thick, while most garage doors are made of 24 gauge metal, which is thinner.
How to Put in a Roll-Up Garage Door: The Best Steps
Install A Roll-Up Doo, To replace your garage door with a roll-up garage door, you need to be safe, have the right materials, and tools, and follow the right steps. Check out this detailed guide on how to frame a roll-up garage door and the step-by-step installation instructions for a roll-up garage door.
You might need some of the following tools for this installation:
- Tape measure, a tool for making a level
- Drills Screwdrivers
- Middle punch
- Vise grips
- C-clamps, torque wrench
- Large wrench for pipes
- Channel-lock pliers
- Electric drill
- A drill for masonry or an impact hammer
- Sling and chain hoist
Step 1: Check the opening for the roll-up garage door
Install A Roll-Up Doo, For the installation to go smoothly, you must accurately measure the space where the garage door will go. Make sure you do the following:
- Compare the size of the door to the size of the hole in the wall.
- Make sure the top and bottom of the door opening are at the same level.
- Make sure door jambs are plumb
- Make sure the track is even with the hole.
- Check for all the parts that go with the setup.
Step 2: Install the door and parts.
Install A Roll-Up Doo, Positioning means putting the door panels and parts used for installation in the door opening. So as to:
- Clean the floor so the curtain doesn’t get scratched or damaged.
- Place the left track on the floor so that it is parallel to the opening, with the bottom of the track against the left door jamb and the top of the track against the inside of the building. Do this step again on the frame’s right side.
- Put all the parts where they belong.
Step 3: Put the brackets in place.
Install A Roll Up Doo, When putting in a roll-up garage door, the brackets hold the panels in place and need to be put in with care:
- Make sure that the short legend is facing up when you put the bracket in place.
- The pawl of the tensioner must be able to move past the ratchet wheel.
- The track and bracket need to be lined up so that the hooks can be put in.
- Combine the bracket and the track so that the locking tab fits into the notch in the bracket.
Step 4: Raise the assembly for the roll-up door.
Once the brackets and track fit together, the whole thing needs to be lifted up and put in place at the top of the door frame. For this step to be done right, it takes two people (or replacements.)
- The bottom tracks should be positioned so that they face the door jambs.
- As you raise the roll-up assembly into place, turn around the jambs.
Step 5: Connect the brackets and tracks to the jambs.
Now, you can put the track and brackets into the door jambs. Use a level to double-check where things are.
- Install A Roll Up Doo, Put the brackets and the tracks on the jambs with fasteners.
- Make sure there is at least one inch of space between the brackets’ back and front.
- On the jamb, the brackets should be in the middle.
- If the door jambs are made of different materials, you’ll need more strong fasteners. The types of fasteners needed for steel, concrete or filled block, and wood are listed in the table below.
Step 6: Adjust the tension on the spring
Install A Roll-Up Doo, After putting the door panels on the brackets, the spring should be tightened to the right amount.
- Install A Roll Up Doo, Turn the door until it is at the right tension. Most of the time, about 1.5 turns.
- Remember to turn the spring in the direction that will make the door move down through the bottom tracks.
Step 7: Put the head stop on the rails.
- When the door is open, the head keeps the roll-up garage door from moving too far and hard into the frame that holds the coiled panels. It has to be put on the track.
- From the inside of each track, you can release the head stop.
- Use a hex screw to hold the head stop to the track.
Step 8: Put in the stop clips, rope, and handles
Install A Roll Up Doo, The roll-up garage door opener needs to be set up. It has stop clips, handles, and a rope.
- Attach the stop clip to the inside bottom of each bar with a carriage bolt and nut.
- Use carriage bolts and nuts to put the handles on the outside of the bottom bar.
- Put the rope through the hole in the middle of the bottom bar angle’s horizontal leg.
Installing a Roll-Up Garage Door Yourself vs. Hiring a Professional
Install A Roll-Up Doo, The instructions for installing a roll-up garage door are simple, but it takes more than one person to do it right. Also, your measurements need to be accurate and level because the door is being pulled up into a coil at the top of the door jab. Lastly, you need the right tools to be able to lift the heavy door assembly into place.
Fixgaragedoors has the skills and tools to take down old garage doors and put up a roll-up garage door right the first time. Our fair prices, high-quality materials, and qualified and trained technicians put safety first and help you avoid getting hurt.
Install A Roll-Up DooM Even though roll-up garage doors can be installed by the homeowner, it is best to let the experts at Fixgaragedoors do it.