How To Paint A Door With A Roller, An antique door can be given new life and made to look like it belongs in the space by giving it a coat of paint. If you use a paint roller instead of painting with a brush, you can skip the lengthy and laborious brush painting process. Rollers function most well on doors that have a predominantly flat surface. They are not appropriate for very ornate or carved doors that need for the dexterity of a brush to delve into the intricate details of the carvings. A smooth coat and an appealing finish can be achieved on the finished door by performing the necessary preparations before beginning and by utilising the roller in the appropriate manner.
Tip
Rollers are available in a range of sizes. On doors that are flat and have no panels, a conventional 9-inch roller works the best. For doors with panels, a tiny roller that is 4 inches in diameter should be used. Choose a paint tray that is proportionately sized to the roller you will be using.
1. Take the Door Off Its Hinge and Set It Aside
If you want the best results, either the door needs to be open or it needs to be taken off of its hinges. If not, painting the edge of the door that is closest to the door frame will be tough. There are two distinct approaches to taking off a door. According to Family Handyman, the best and most straightforward method is to take out the hinge pin from the hinge. This ensures that the hinges that are already bolted into the door frame remain in place. If the pin is not tightly secured, you may be able to remove it by hand by twisting it.
You might also try using a hammer and the point of a nail to tap it out from underneath using the alternative method. If the hinge will not budge, use a drill with the chuck turned anticlockwise to loosen the screws holding the hinges in place, and then remove the door using this method.
2. Get the Door Ready to Be Painted
Sand the entire surface of the door so that it is ready to be painted. If you want the new paint to apply more uniformly across the door, use a sanding pad with 120 grit to smooth out any rough places and dull the finish that is already there. To remove sanding residue from the door, wipe it down with a towel that has been gently wet. According to Bob Vila, the procedure of painting a metal door as opposed to a wooden door is the same, with the exception that you will want to clean the metal door with a degreaser before you begin the painting process.
3. Prime the door before painting it.
Primers should be poured into the reservoir located at the foot of the slope in the paint tray. When working with paints that are water-based, use a primer that is also water-based, and when working with colours that are oil-based, use a primer that is oil-based. According to Bob Vila, if you are painting a door that has inset panels, you should paint or prime those panels before the rest of the door using a smaller brush. After that, you should use a roller to rapidly finish the task.
4. Start the process of priming the door.
Take a paintbrush with a width of 1 inch and dip it into the primer. To eliminate the surplus, remove it by tapping the edge of the bristles against the side of the tray. Use the brush to paint the area along the edge of the door as well as the edges of any panel insets on the door. The procedure in question is known as cutting in. Make cuts all the way around the door handles and the latches.
5. Coat the Roller with Primer and Set It Aside
To remove extra paint, roll the paint roller through the primer that is contained in the tray reservoir and then up the ramp. This will result in the paint being squeezed out.
6. Door of Prime Quality with a Roller
Long, even strokes should be used when rolling the roller up and down the door. To get an even coat, you may need to roll it through the primer that is contained in the tray. Wait the required amount of time for the primer to completely dry, which is often between two and three hours.
7. Get the Paint Ready for the Door
Paint of the selected colour should be poured into a freshly cleaned paint tray.
8. Make Slashes in the Paint
Make cuts along the door’s edges using a paintbrush and the colour you want to use for the paint. Applying the paint to the remaining portion of the door should be done using the same rolling technique that was utilised when applying the primer. After the initial coat of paint has had ample time to dry, a second coat can be applied, if necessary.
9. Rehang the Door That Has Been Painted
After the door has had enough time to thoroughly dry and the colour has reached the desired state, you can rehang it. Because changing the hinge pins requires that the door be aligned with the hinges in order for the pin to slide all the way in, it is ideal to have an assistant for this step. If you do not have an assistant, this step will be more difficult. In the event that you were forced to take out the screws, the door will need to be propped up while the hinges are repaired.
